COB Led Strip 75W Amber Light 24V IP20 PCB 10mm Continuous Led Chip en
  • COB Led Strip 75W Amber Light 24V IP20 PCB 10mm Continuous Led Chip en
  • COB Led Strip 75W Amber Light 24V IP20 PCB 10mm Continuous Led Chip en

Type of device:
Led Strip
Ideas of Use:
Creating Effects
Ideas of Use:
Ambient Lighting
Output:
DC 24V
Kelvin :
Amber
Watts:
15 W / Metro
Lumen - Brightness:
1600 Lumen / Meter
Quantity Led:
Led Continued
IP rating:
IP20
Cutting Length:
45,45 mm
Width:
10 mm
Length:
5 Meters
CRI:
N.D.
Light Angle:
160°
Dimmable:
Yes
Series:
Strip Led COB
Immagine per Categoria Specifica

Led Strip COB Amber Light 75W 24V IP20 PCB 10mm Chip Led Continued

4835

€56.50
,
5/ 5
22% Tax included
3 Giorni | 0 Ore | 0 Minuti | 0 Secondi
Quantity
-
+
Totale:
22% Tax included


Spedizione gratuita a partire da 59€
Garanzia minima 2 anni
Sostituzione e consegna in 3 giorni lavorativi
Reso fino a 30 giorni
Spedizione entro 24/48h
Oltre 40000 recensioni

Chiamaci +39 0392271928
Richiedi Assistenza
Contattaci tramite Whatsapp

Lun - Gio 9h - 18:30h | Ven 9h - 18h

DESCRIPTION
• Led Strip composed of 1 Single COB Led
• Absolute zero light point effect.
• Power supply DC 24V (Power supply not included)
• Dimmable and Cuttable Led Strip at every 45.45 mm
• Nominal Power 75W per Coil / Power Consumption 15W / mt
• Amber light
 
5-meter COB LED strip, mounted on Tesa's double-sided adhesive tape. Single Led that can be cut at every 45.45 mm. No more light point effect, this Led strip definitively eliminates any light point effect. The light is homogeneous, compact and bright.

DATA SHEET
PCB width 10mm
PCB + SMD height 1.6mm
Coil length 5mt
DC 24V power supply
Nominal Power 75W
Effective Power 15W / mt
Effective Lumens 1600 lm / mt (Indicative Value, colored light has no lumens)
Kelvin AMBER
COB Led type
Cuttable to Each 45.45 mm
IP20 waterproofing
Dimmable: YES
Operating temperature -20 ° to + 40 ° degrees
CE / RoSH certifications
3 Years Warranty
 
The connection of several Led strips must be carried out in parallel. For installation it is necessary to use aluminum profiles for dissipation.


——————————————————————————————————————————————————————————————————————————————————————————————————————————
CORRECT INSTALLATION
To ensure maximum performance in terms of light output and duration, installation on a special aluminum profile is mandatory, designed for correct heat dissipation.
The aluminum profiles not only dissipate heat, but also protect the LED strips from dust, insects and partially moisture.
 
PROPER NUTRITION
The LED strips must be powered with a constant voltage power supply, usually with the DC symbol.
With a power that is equal to or greater than the consumption of the length required for installation.
For example, for 24V LED strips with a consumption of 50W per 5 meters, a DC 24V power supply with a wattage of 50W, 60W, 75W, or higher is required.
The voltage drop can affect the length of the LED strip installed ... normally it is recommended to install a maximum of 5 to 10 meters for each continuous line.
To reach greater lengths, it is mandatory to power the Led Strip at both ends or at each 5m section.
Amplifiers are used for multicolored LEDs.
  
DIMMERATION
To adjust the light intensity of a LED strip, it is necessary to use a receiver that acts as a controller with a PWM signal.
Control modes vary by device type.
You can dim the Led strips with a Wi-Fi controller, from Pushbutton, use Alexa's voice control, remotely manage via Smartphone and even set a timer.
4835

Data sheet

Type of device
Led Strip
Ideas of Use
Ambient Lighting
Creating Effects
Output
DC 24V
Kelvin
Amber
Watts
15 W / Metro
Lumen - Brightness
1600 Lumen / Meter
Quantity Led
Led Continued
IP rating
IP20
Cutting Length
45,45 mm
Width
10 mm
Length
5 Meters
CRI
N.D.
Light Angle
160°
Dimmable
Yes
Series
Strip Led COB